Game Download

UNLOCKING THE BOOTLOADER
Downloads:

Unlock bootloader

Requirements:
PC companion
Flash tool (Download follow the instruction given)
Rooted e10i phone(check ma previous post on rooting )


Basic step:
Install PC companion
Install flash tool
Go to C:/Flashtool:/Driver:/
Click on driver
Select your device adb and select flash tool drivers
Install
NOte: Its best to turn of your ANtivirus

Steps:

1.Extract the downloaded file
2.Open S1tool.exe
3.Click identify button
4.Turn of your phone and pin the usb cable to the phone
5.Hold the back button
6.Now plug in the usb cable to  PC (Now the LED of your phone should be in green color)
7.U ll get the code as below


Code:
4/10/2012 21:41:44 Welcome to S1 identify tool
4/10/2012 21:45:13
4/10/2012 21:45:13 TO CONNECT NEXT PHONES
4/10/2012 21:45:13 X10 Xperia,E10 Xperia Mini,E15 Xperia X8,U20 Xperia Mini Pro
4/10/2012 21:45:13 LT15 Xperia ARC,MT15 Xperia NEO,R800 Xperia PLAY
4/10/2012 21:45:13 PRESS AND HOLD "BACK" BUTTON...
4/10/2012 21:45:13
4/10/2012 21:45:13 PLEASE ATTACH TURNED OFF PHONE NOW
4/10/2012 21:45:13
4/10/2012 21:45:46
4/10/2012 21:45:46 RUNNING S1_EROM VER "r8A029"
4/10/2012 21:45:46 SOFTWARE AID: 0001
4/10/2012 21:45:46 LOADER AID: 0001
4/10/2012 21:45:49 FLASH ID: "002C/00BC"
4/10/2012 21:45:49 LOADER VERSION: "R4A045"
4/10/2012 21:45:49
4/10/2012 21:45:49 MODEL (from GDFS): X10
4/10/2012 21:45:49 SOFTWARE VERSION: 1236-9291_2.1.1.A.0.6
4/10/2012 21:45:49 CUSTOM VERSION: 1241-3178_R1B
4/10/2012 21:45:49 FILESYSTEM VERSION: WORLD-1-8_2.1.1.A.0.6
4/10/2012 21:45:49 SERIAL NO: CB511SPH7Q
4/10/2012 21:45:49
4/10/2012 21:45:49 SEMC SIMLOCK CERTIFICATE
4/10/2012 21:45:49 Elapsed:36 secs.

8. See the code above "Elapsed:36 secs" it shows SEMC SIMLOK CERTIFICATE
9.If your code shows same then run msm7227_semc.cmd from the downloaded file
10.If your code shows only SIMLOCK CERTIFICATE or any other run msm7227_setool2.cmd

Code should be like this:


process requires standard 2.x android firmware.
Press any key to continue . . .
Getting ROOT rights.
1743 KB/s (585731 bytes in 0.328s)
error: protocol fault (no status)
Waiting ...
Removing NAND MPU restrictions via SEMC backdoor. Permanent. Require ROOT rights.
192 KB/s (3087 bytes in 0.015s)
success
Waiting ...
Getting ROOT rights.
Waiting ...
Writing patched semcboot. Two step process
First, we need get access to semcboot area
504 KB/s (8064 bytes in 0.015s)
Second, we need to write semcboot ;)
1130 KB/s (596916 bytes in 0.515s)
successfully wrote 0003ff00
Press any key to continue . . .



How to check :

Now switch off your phone
Run setool.exe
hold back button and connect the usb as mentioned in previous step
If the line RUNNING S1_EROM FROM VER "#8A02$" has a lowercase "r" letter replacing the "#" (RUNNING S1_EROM FROM VER "r8A02$"), your bootloader has been unlocked . If it has an uppercase "R" replacing the "#" (RUNNING S1_EROM FROM VER "R8A02$"), your bootloader is NOT unlocked




What if some thing went wrong???????




1. My SIM Card is not recognised after unlocking phone with msm7227_setool2.cmd!
Ans: Redo unlocking procedure (step 5 onwards) using msm7227_semc.cmd.

2. I get lots of "Access is denied" messages while unlocking!
Ans: Disable your antivirus and try the unlocking process again. Antivirus finds a virus in ADB.exe even though there isnt one!

3. I get some "error: protocol fault" messages!
Ans: Its normal and this isnt a problem. This is because the tool is inquiring for your phone while the phone is rebooting. USB debugging mode isnt on when phone is rebooting so it causes some errors. Eventually, your phone will connect with your PC so this is not an issue.

4. I get some "exec /system/bin/sh failed" messages!
Ans: Reroot your phone (refer ma previous post on rooting)

Stop right there Check ma other post on how to install custom rom for e10i



RELOCKING THE BOOTLOADER


1. Turn off your phone.

2. Launch s1tool.exe in the folder you extracted s1tool to.

3. Click on Restore button and then connect your phone to the PC in flash mode (press and hold back button while connecting your phone to the PC).

4. Wait for the process to complete. Congratulations! You now have relocked your bootloader!

5. To check, open s1tool.exe, click IDENTIFY button, turn off your phone, connect it in flash mode to the PC (press and hold back button while connecting your phone to the PC. The LED on your phone should flash green).

6. Continue holding back button until there is some output.



If the line RUNNING S1_EROM FROM VER "#8A02$" has a lowercase "r" letter replacing the "#" (RUNNING S1_EROM FROM VER "r8A02$"), your bootloader has been unlocked . If it has an uppercase "R" replacing the "#" (RUNNING S1_EROM FROM VER "R8A02$"), your bootloader is NOT unlocked